How to Propagate Rubber Plant in Water: 3 Easy Steps

Some of the links in this post may be affiliate links.

Propagating rubber plants is actually quite simple, but there are some important pieces of information to know otherwise it will not work. Keep reading to learn everything you need to know, and I’ll show you some helpful pictures along the way in this step-by-step guide. 

how-to-propagate-rubber-plant-in-water

There are quite a few ways that you can propagate rubber plants (Ficus elastica), but the water propagation method may be the easiest, especially for the beginner, so I will solely focus on this method for this post.

You may also wish to experiment with air layering and soil propagation in the future. All of these methods will result in a new plant, and it’s fun to try different methods.

HOW TO PROPAGATE RUBBER PLANT IN WATER

Regardless of the rubber plant type you have, you can use this water method for propagation. You can really propagate at any time of year, but the best time to do it is during the growing season.

Early spring through late summer works well. However, if you have enough light (either in a greenhouse or if you’re growing plants under lights year round), you can safely do it anytime!

1. Make Your Rubber Plant Cuttings 

The first step is to get a nice pair of sharp pruners, or a sharp knife, and make your cuttings. Wipe down your tools with isopropyl alcohol to sterilize them right before you make cuttings. By taking cuttings of your rubber tree, you’re also helping your mother plant branch out more and become more bushy.

how-to-propagate-rubber-plant-in-waterhow-to-propagate-rubber-plant-in-water

So not only can you get a new rubber plant out of all this, but you’re also helping your original rubber plant branch out and become fuller.

This is particularly helpful if you have a rubber plant that only has one trunk.

​So if you do want your rubber plant to branch out, you’ll simply want to cut the branch wherever you want it to branch out. Take a look at this mother plant below. You can see exactly where it was cut on top. And you can clearly see two areas of new growth! Those reddish buds are new branches starting to grow. 

how-to-propagate-rubber-plant-in-waterhow-to-propagate-rubber-plant-in-water

Select a healthy stem and cut the branch right above a leaf (maybe 1/2 inch to an inch above the leaf). Keep in mind that as soon as you make your cut, the stem will start to ooze out a white, milky sap. You may want to wear protective gloves because the white sap can cause skin irritation.

If you’ve touched the sap with your bare skin, be sure to wash up with soap and water.

The white sap will start to drip quickly, so I like to have a damp paper towel or damp cloth handy to clean it up before it dries. 

variegated-rubber-plant-white-sapvariegated-rubber-plant-white-sap

Next, if the part that you cut off is rather large, you can make multiple cuttings. In fact, you can even make cuttings that consist of a single leaf, but the leaf needs to have part of the branch/stem attached.

If you just cut a single leaf and don’t include part of the branch or stem, your cutting will grow roots, but it will not develop into a plant. 

Take a look at the cutting below. You can make multiple cuttings like this. You need to include a leaf node in each cutting in order for it to result in a new plant. The node is simply the area where the leaf and petiole grow out of the branch.

how-to-propagate-rubber-plant-in-waterhow-to-propagate-rubber-plant-in-water

Now, your cuttings can also have more than one leaf, but make sure that the cutting doesn’t have a ton of leaves. Two or three leaves is plenty.

Once you’ve made your cuttings, it would be a good idea to let them sit and air dry for a few minutes. Wait until the white sap has stopped “bleeding” before proceeding to the next step.

2. Place Rubber Tree Cuttings in Water

Next, you’ll want to place your stem cuttings in a cup or glass jar and add some water. Tap water is perfectly fine to use. It’s OK to have both cut ends of the stem under water. If you have a longer cutting, just make sure the bottom couple inches (at least) is underwater. 

how-to-propagate-rubber-plant-in-waterhow-to-propagate-rubber-plant-in-water

When I rooted the cuttings shown in this post, I actually noticed new branches starting to form before the roots started to grow. This is perfectly normal and you may also observe the same thing.

I didn’t notice roots starting to form until about 3-4 weeks. The roots will look a little different than you are used to. The new roots will look like irregular, white stubs, and at first glance, they will almost look like mealybugs! But the longer you wait, they will start to grow more and look like normal roots. 

how-to-propagate-rubber-plant-in-waterhow-to-propagate-rubber-plant-in-water
Notice the reddish new growth starting, as well as the start of new, white roots

Be sure to change the water frequently, particularly in the beginning of the rooting process. Change the water at least once or twice a week, or even more frequently if the water looks dirty or cloudy. If the water looks clean, it’s OK to just top off the water level. Just make sure it doesn’t completely dry up!

​Place your cuttings in a nice warm spot with plenty of light. Right in front of a window is great, and even some direct sun is fine, particularly if you have a window that has morning sun. Don’t place your cuttings in a dark corner because it will minimize your chances of success or greatly delay the rooting process. 

Here is another cutting I made and started to root. I included a much larger piece of branch versus the other cuttings. Notice that there are 3 new growths starting where the red arrows are.

propagating-rubber-plant-in-waterpropagating-rubber-plant-in-water

3. Pot Up Your Rooted Cutting

​Once you notice roots starting to grow, you can go ahead and pot up each cutting in a small pot. You can wait until the roots are about 1/2 an inch to an inch long and give each cutting its own pot. I would recommend a 4-inch diameter pot to start with.

If your cutting has small reddish branches forming like you’ve seen in this post, it is OK if it is buried under the soil line, particularly if you took a single node cutting with only a very small portion of branch.

Here is the cutting before I inserted it into a small pot of soil. It already has the start of roots, and you can see the reddish branch starting to form.

how-to-plant-rubber-tree-cuttingshow-to-plant-rubber-tree-cuttings

And here is the cutting after I planted it in the soil. You can see that the new reddish growth is right under the soil line. Soon, it will emerge from the soil line and the roots will continue to develop.

how-to-plant-rubber-tree-cuttingshow-to-plant-rubber-tree-cuttings

Once the plant gets established and is root-bound, you can give it a larger pot. Check out my post for best soil for rubber plants where I give you 3 excellent options to help ensure you have healthy plants! 

Water when the surface of the soil feels dry. Do not let the soil completely dry out as this will hinder rooting and early development of your plant.

​If you’ve enjoyed this post, you may also enjoy my other rubber plant related posts so you can ensure that your plant is well cared for:

Rubber Plants Ultimate Growing Guide + 16 Common Problems

Rubber Plant Aerial Roots

Air Layering Rubber Plants

For the best chance of success, if you can, I always recommend making more than one cutting when propagating any indoor plants in case one doesn’t take.

Have you tried to propagate rubber plants in water? Comment below. I’d love to hear!

We will be happy to hear your thoughts

Leave a reply

Urbanherbgardens.com
Logo
Shopping cart